Outside lower fork tube diameter

[Mscb1100]

Does anyone know the lower fork tube measurement in inches and or mm? I need to order some fittings to install some Denali lights I have left over from another project.
Thanks

[Aussieflyer]

(01-12-2018 02:13 PM)Mscb1100 Wrote:  Does anyone know the lower fork tube measurement in inches and or mm? I need to order some fittings to install some Denali lights I have left over from another project.
Thanks

Not sure where you're planning to mount the lights ...
The section just below the mudguard mount and above disc rotor has room for bracket. It measures 2" OD.

[Mscb1100]

(01-12-2018 03:19 PM)Aussieflyer Wrote:  

(01-12-2018 02:13 PM)Mscb1100 Wrote:  Does anyone know the lower fork tube measurement in inches and or mm? I need to order some fittings to install some Denali lights I have left over from another project.
Thanks

Not sure where you're planning to mount the lights ...
The section just below the mudguard mount and above disc rotor has room for bracket. It measures 2" OD.

On the fork leg just below the fork seal
No mudguard on US models that I know of on the forks



Sent from my iPad using Tapatalk

[Aussieflyer]

(01-12-2018 03:31 PM)Mscb1100 Wrote:  

(01-12-2018 03:19 PM)Aussieflyer Wrote:  

(01-12-2018 02:13 PM)Mscb1100 Wrote:  Does anyone know the lower fork tube measurement in inches and or mm? I need to order some fittings to install some Denali lights I have left over from another project.
Thanks

Not sure where you're planning to mount the lights ...
The section just below the mudguard mount and above disc rotor has room for bracket. It measures 2" OD.

On the fork leg just below the fork seal
No mudguard on US models that I know of on the forks



Sent from my iPad using Tapatalk

The widest OD of the fork lower, where the seal seats, is 62.9mm.
The narrowest OD of the fork lower is 50.9mm.
All models have lugs for a mudguard, perhaps it's a terminology thing. What do you call that half round metal thing over the top of the front wheel ... a fender?

[Mscb1100]

(01-12-2018 03:49 PM)Aussieflyer Wrote:  

(01-12-2018 03:31 PM)Mscb1100 Wrote:  

(01-12-2018 03:19 PM)Aussieflyer Wrote:  

(01-12-2018 02:13 PM)Mscb1100 Wrote:  Does anyone know the lower fork tube measurement in inches and or mm? I need to order some fittings to install some Denali lights I have left over from another project.
Thanks

Not sure where you're planning to mount the lights ...
The section just below the mudguard mount and above disc rotor has room for bracket. It measures 2" OD.

On the fork leg just below the fork seal
No mudguard on US models that I know of on the fender



Sent from my iPad using Tapatalk

The widest OD of the fork lower, where the seal seats, is 62.9mm.
The narrowest OD of the fork lower is 50.9mm.
All models have lugs for a mudguard, perhaps it's a terminology thing. What do you call that half round metal thing over the top of the front wheel ... a fender?

In Mississippi that half round metal thing over both wheels is typically called and spelled “fenda” lol
Seriously, thanks for the measurements.
We call a rubba flap hangin frum the fenda a mudguard

---

Aussieflyer
Do you have a side view picture or your bike
It has an interesting paint scheme

[Aussieflyer]

MSCB you're welcome.
There are a few pics in this post:
http://cb1100forum.com/forum/showthread....974&page=6