Guth
Forum Founder
Portland, OR
Posts: 3,918
Joined: Apr 2013
|
RE: Staintune
(01-23-2018 06:21 PM)PowerDubs Wrote: Sounds like you had it mounted wrong!
It is possible to have the flange on the wrong side- which would be problematic.
The correct placement is with the Staintune's bracket mounted on the inside of the rear footrest perch. The incorrect placement is to the outside of that perch, which would move it further away from the rear shock.
The Honda CB1100: STILL air-COOLed
Deposit placed 11/12/2012.
Received delivery 04/05/2013.
|
|
01-23-2018 06:38 PM |
|
Gumby 1100
Running Like a Top
Cambridge, Ontario, Canada
Posts: 489
Joined: May 2014
|
RE: Staintune
(01-23-2018 06:21 PM)PowerDubs Wrote: Sounds like you had it mounted wrong!
It is possible to have the flange on the wrong side- which would be problematic.
No, it was mounted correctly with the flange on the proper side of the footrest stay.
You would need to have installed a Staintune on a 2014 to understand this. It would be next to impossible to mount it wrong as Guth noted (on the outside of the footrest stay), because it would then be so far away and out of alignment with the header pipe that you would never get the compression joint sealed (or it would be extremely difficult to tighten the clamp and you could mangle things in the process).
This is a documented problem with the position/angle of the welded hanger bracket, and not me (Although, I, personally, have other documented problems).
Jim21680 was the one with the worst clearance. Check out his posts and mine below:
(Starting at about page 18)
http://cb1100forum.com/forum/showthread....=staintune
2014 CB1100A (Canadian) #068 (Sold)
2018 Harley-Davidson Road King
(This post was last modified: 01-23-2018 07:07 PM by Gumby 1100.)
|
|
01-23-2018 06:55 PM |
|
PowerDubs
Road Warrior
NWNJ
Posts: 2,857
Joined: Jul 2016
|
Staintune
Mine is a 2014. Installed with zero issues.
I’ll check those pictures tomorrow and then check my bike.
Sent from my iPhone using Tapatalk
104whp / 75wtq ... for now.
|
|
01-23-2018 07:47 PM |
|
Townie
1st Service Completed
Ontario, Canada
Posts: 116
Joined: May 2015
|
RE: Staintune
(01-23-2018 06:55 PM)Gumby 1100 Wrote: (01-23-2018 06:21 PM)PowerDubs Wrote: Sounds like you had it mounted wrong!
It is possible to have the flange on the wrong side- which would be problematic.
No, it was mounted correctly with the flange on the proper side of the footrest stay.
You would need to have installed a Staintune on a 2014 to understand this. It would be next to impossible to mount it wrong as Guth noted (on the outside of the footrest stay), because it would then be so far away and out of alignment with the header pipe that you would never get the compression joint sealed (or it would be extremely difficult to tighten the clamp and you could mangle things in the process).
This is a documented problem with the position/angle of the welded hanger bracket, and not me (Although, I, personally, have other documented problems).
Jim21680 was the one with the worst clearance. Check out his posts and mine below:
(Starting at about page 18)
http://cb1100forum.com/forum/showthread....=staintune
My experience was the same as Gumby's and Jim's, that is, very tight clearance to the lower shock bolt, almost touching. Before I ordered my Staintune, I asked Staintune if they had resolved this issue, and they said they had. But out of the box, when installed, it almost touched the lower shock bolt. Slightly bending the mounting flange gave me ~1/4" clearance.
I have a 2014 standard.
|
|
01-23-2018 08:20 PM |
|
Banned
Banned
earth
Posts: 644
Joined: May 2017
|
RE: Staintune
Well, some minor tweaking won't bother me.
As soon as I get my luggage issue sorted out on the CB (have to get ready for the rally) I'm ordering a Staintune.
Thanks everyone.
|
|
01-24-2018 03:58 AM |
|
Guth
Forum Founder
Portland, OR
Posts: 3,918
Joined: Apr 2013
|
RE: Staintune
That's the spirit W/R!
(Although I'd much prefer to learn that when your Staintune arrives you're able to totally skip the tweaking mode and move straight on to the full enjoyment mode of ownership.)
The Honda CB1100: STILL air-COOLed
Deposit placed 11/12/2012.
Received delivery 04/05/2013.
|
|
01-24-2018 07:02 PM |
|
Banned
Banned
earth
Posts: 644
Joined: May 2017
|
RE: Staintune
I solved my luggage issue today - I'm buying lash's rear carrier, Givi top box and Daytona seat so I'm all set for the rally in June.
I'll wait a month or so for my wife to calm down from that purchase before I order the Staintune.
After perusing the interwebs it seems that ordering direct from Staintune is the way to go?
|
|
01-24-2018 07:48 PM |
|
Gumby 1100
Running Like a Top
Cambridge, Ontario, Canada
Posts: 489
Joined: May 2014
|
RE: Staintune
(01-24-2018 07:48 PM)W/R Wrote: After perusing the interwebs it seems that ordering direct from Staintune is the way to go?
Yes, but after getting an order confirmation from them, request a shipping confirmation as well that clearly shows your name and address.
After waiting some 2 months after ordering and paying for mine, I finally asked what the delay was. Turned out they shipped mine to another CB owner and then had to rush another through production for me...so, yet another few weeks delay! Maybe the "hanger tab alignment" issue was a mistake due to haste!
All said, it was worth the wait and any installation hassles!
And, you should easily be able to sell it when you sell the CB...I'm pretty sure that bigsheep is happy with mine, but he hasn't had much nice riding weather yet to really appreciate it...
2014 CB1100A (Canadian) #068 (Sold)
2018 Harley-Davidson Road King
(This post was last modified: 01-24-2018 08:42 PM by Gumby 1100.)
|
|
01-24-2018 08:04 PM |
|
jedd
Running Like a Top
Austin, TX
Posts: 417
Joined: Dec 2015
|
RE: Staintune
Correct me if I'm wrong, but Staintune isn't making any slip-ons for the 2010-2016 DLX/EX models?
b/c I don't see any twin tips from them.
|
|
01-25-2018 09:20 AM |
|
Gumby 1100
Running Like a Top
Cambridge, Ontario, Canada
Posts: 489
Joined: May 2014
|
RE: Staintune
(01-25-2018 09:20 AM)jedd Wrote: Correct me if I'm wrong, but Staintune isn't making any slip-ons for the 2010-2016 DLX/EX models?
b/c I don't see any twin tips from them.
No, I don't think Staintune have the dual slip-ons yet.
Your best bet would probably be the Over Racing Dual Slip-Ons from Samurider...
https://www.samurider.com/?p=22310
Although, it looks like Arrow now has Dual Slip-Ons and a new 4-into-2 header available for the DLX/EX...
https://www.arrow.it/en/assembled/1525
2014 CB1100A (Canadian) #068 (Sold)
2018 Harley-Davidson Road King
(This post was last modified: 01-25-2018 09:38 AM by Gumby 1100.)
|
|
01-25-2018 09:28 AM |
|
|
Forum Friends
|
|
Recent Posts
|
Shifting issue
|
My young lads 2004 EX250F was dragging t . . .Tev62 — 06:44 AM |
Hanging up the helmet
|
If I thought I could still be riding at . . .Tev62 — 06:38 AM |
Shifting issue
|
It may be interesting, but it won’t be . . .Cormanus — 04:34 AM |
Shifting issue
|
This thread is shaping up to be some int . . .GoldOxide — 04:27 AM |
Shifting issue
|
Ah. Thank you. That makes sense.
Need t . . .Cormanus — 09:18 PM |
Shifting issue
|
Here is what my clutch basket looks li . . .pekingduck — 09:01 PM |
Shifting issue
|
When bleeding a hydraulic clutch, I fou . . .MMC — 08:14 PM |
What did you do to/with your other bike?
|
The flag is apparently from Costa Rica. . . .pdedse — 07:47 PM |
Statistics
|
» Members: 6,509
» Latest member: Smitty
» Forum threads: 15,966
» Forum posts: 329,525
Full Statistics
|
|
|