Post Reply 
 
Thread Rating:
  • 7 Votes - 2.86 Average
  • 1
  • 2
  • 3
  • 4
  • 5
What did you do on, or to, your CB today?
Author Message
shdwghst457 Offline
Running Like a Top

San Antonio, TX
Posts: 476
Joined: Feb 2014
Post: #21
RE: What did you do on, or to, your CB today?
Well you could fix your problem Honda's way; replace all of your bikes with 2014s!

'13 - #000955
06-19-2014 02:11 PM
Find all posts by this user Quote this message in a reply
Cormanus Offline
Moderator

Queensland, Australia
Posts: 11,352
Joined: Dec 2013
Post: #22
RE: What did you do on, or to, your CB today?
Can't get a 2014 CB1100 here.
06-19-2014 03:54 PM
Find all posts by this user Quote this message in a reply
jchoby Offline
1st Service Completed

Ohio
Posts: 116
Joined: Oct 2013
Post: #23
RE: What did you do on, or to, your CB today?
I dropped my phone on my tank and chipped the paint….a tiny chip but it pains me to no end. Next time not only will I pull over and stop…I'll get off the bike.
06-19-2014 03:55 PM
Find all posts by this user Quote this message in a reply
The ferret Offline
Forum Moderator

Ohio
Posts: 19,853
Joined: Apr 2013
Post: #24
RE: What did you do on, or to, your CB today?
(06-19-2014 03:55 PM)jchoby Wrote:  I dropped my phone on my tank and chipped the paint….a tiny chip but it pains me to no end. Next time not only will I pull over and stop…I'll get off the bike.


Ooooh a bad word moment.. Probably several bad words

.
2014 DLX and 2006 ST 1300

It doesn't matter what I ride, where I ride, or how far I ride... it only matters THAT I ride...every day...Ferret
06-19-2014 04:17 PM
Find all posts by this user Quote this message in a reply
shdwghst457 Offline
Running Like a Top

San Antonio, TX
Posts: 476
Joined: Feb 2014
Post: #25
RE: What did you do on, or to, your CB today?
Cormanus, could that have something to do with why it didn't make it to AU? Are there laws there describing the switch layout?

'13 - #000955
06-20-2014 08:39 AM
Find all posts by this user Quote this message in a reply
Cormanus Offline
Moderator

Queensland, Australia
Posts: 11,352
Joined: Dec 2013
Post: #26
What did you do on, or to, your CB today?
No. I think switch layout is up to manufacturers. The 2013 and 2014 models didn't come here because the 2010 and 2011 models didn't sell too well.
06-20-2014 06:29 PM
Find all posts by this user Quote this message in a reply
shdwghst457 Offline
Running Like a Top

San Antonio, TX
Posts: 476
Joined: Feb 2014
Post: #27
RE: What did you do on, or to, your CB today?
Ah. Didn't realize '13 didn't make it either.

'13 - #000955
06-20-2014 09:42 PM
Find all posts by this user Quote this message in a reply
Greg Offline
1st Service Completed

Central Florida
Posts: 190
Joined: Apr 2013
Post: #28
RE: What did you do on, or to, your CB today?
(06-19-2014 03:55 PM)jchoby Wrote:  I dropped my phone on my tank and chipped the paint….a tiny chip but it pains me to no end. Next time not only will I pull over and stop…I'll get off the bike.

There is a lengthy thread here about applying clear vinyl film to protect the tank. I put 3M clear bra protection film on the top surface of my red 2013 tank and am getting ready to put Avery clear paint protection vinyl film on my new white tank.

There is a much easier and more precise way to trim the vinyl than messing with templates.

I first applied knifeless tape to the tank where I wanted to trim the vinyl. Cut the vinyl to overlap the trim tape and apply it. The knife less tape works with both wet and dry install. I think wet install is best for clear to avoid fingerprints and bubbles.
06-21-2014 01:26 PM
Find all posts by this user Quote this message in a reply
Jim21680 Offline
Running Like a Top

Philadelphia, PA
Posts: 315
Joined: Jul 2013
Post: #29
RE: What did you do on, or to, your CB today?
Today I pulled off the fenders to clean some rust that had developed. The front is delightfully easy to remove; the rear is a bit more work. I figured this might be a yearly task, so I cut the brake light's 3 wires, and installed a few quick-disconnects. This worked very nicely, and makes the rear fender removal much easier. Gave it a good cleaning too...as others have said, WD-40 works great for the wheels.

I was looking around for advice on some kind of under-fender protectant, and surprisingly didn't find too much. I thought for sure this would be a problem the Harley & metric cruiser guys commonly dealt with, but maybe not. I ended up just applying a couple heavy coats of Turtle Wax, so we'll see how that holds up. The bike does look quite different with them off!


Attached File(s) Image(s)
   
06-21-2014 02:43 PM
Find all posts by this user Quote this message in a reply
Cormanus Offline
Moderator

Queensland, Australia
Posts: 11,352
Joined: Dec 2013
Post: #30
What did you do on, or to, your CB today?
Jim's photo ....

İmage
06-21-2014 03:51 PM
Find all posts by this user Quote this message in a reply
Post Reply 


[-]
Forum Friends
Premium Exhausts & Unique Parts from Japan

[-]
Recent Posts
At what RPM do you cruise?
My CB likes 2500 rpm. I have the Yoshi R . . .Hondakid — 09:43 PM
CB1100 Idle speed instability problem
Dave Sorry that the IACV replaceent i . . .SportsterDoc — 09:26 PM
I think Its Done
Many thanks. RonaldNicki-nitro — 08:41 PM
Staintune
ouch.......i thought since they were tal . . .misterprofessionality — 08:32 PM
Staintune
The $800 is just for the slip on.The ferret — 07:41 PM
CB1100 Idle speed instability problem
Thanks for the kind words of support. I . . .Dave — 07:07 PM
Hello from Hawaii
Welcome Sloro! Beautiful bike! Is . . .sloro — 07:01 PM
Todays weather
I'm traveling on business in Nebraska an . . .Stichill — 06:42 PM

[-]
Statistics
» Members: 4,082
» Latest member: AJay80
» Forum threads: 10,548
» Forum posts: 193,205

Full Statistics

>
Forum Jump: